Zum Inhalt springen

Land und Sprache

1 Warenkorb
body line

Body Line Dent Repair: When PDR Can Fix a Crease

When a dent on a body line or a crease can be fixed with PDR, the four checks to make before you quote, how to get access, and the sequence that brings the line back sharp.

The rear quarter panel of a graphite-grey car in a PDR workshop at sunset, a crease dent kinking the golden reflection along its body line, PDR rods racked by the open door and an orange glue tab on a cart

Workshop-Podcast · 4 Min. Hörzeit

Florence, Oliver, Kaan

0:003:49

Transkript37 Zeilen

Body line dent repair with PDR works when the dent is soft, the paint is not cracked and you can reach the line from behind or pull it with glue. A sharp, pinched crease on a body line, cracked paint or a dent on the edge of a panel usually cannot be fixed without paint. When it can be fixed, the order matters more than the force: you release the tension at the ends of the damage first, rebuild the line from the ends toward the centre, and knock down every crown beside it. This guide shows the checks to make before you quote, how to get access, and the sequence that brings a body line back sharp.

Key takeaways

  • A body line dent is a dent that crosses or flattens a stamped feature line. A crease is a fold made by something sliding along the panel. Many repairs are both.
  • Soft dents in body lines are a normal PDR job. Sharp dents on contours, dents on panel edges and anything with cracked paint are not.
  • Look at the paint on the line with a magnifier before you touch it. The line is where the paint has the least room to flex.
  • Work from the ends of the damage toward the centre, in small moves, and read the line board after every few pushes.
  • The line is right when it matches the same line on the other side of the car, not when it looks straight on its own.

Body line dents and creases: what you are looking at

A body line is a stamped ridge, and a dent on it breaks a straight reflection that every eye reads at once.

Manufacturers press body lines (also called character lines or feature lines) into door skins, fenders and quarter panels. The sharp ridge makes the panel stiffer, and it sends a long, straight reflection down the side of the car. That is why a small dent on a body line is easier to see than a bigger dent on a flat area: the eye picks up the kink in the reflection before it sees the dent.

A crease is different. It is made when something travels along the panel instead of hitting it straight on: a shopping cart, a bumper in a car park, a bike handlebar. The metal folds along a line, and the fold holds the surrounding metal under tension. A crease can be anywhere on the panel. When it runs into or along a body line, you have both problems at once.

The practical difference for the technician: a dent on a body line is mostly about rebuilding a sharp edge to its original height. A crease is mostly about releasing tension in the right order, so the metal does not move somewhere you did not want it to.

Can PDR fix a body line dent? Four checks before you quote

Yes, when the dent is soft, the paint is intact, the damage is away from the panel edge and you have a way in.

The OEMs say the same thing. General Motors' service bulletin on paintless dent repair lists "soft dents in body lines and contoured areas that allow reasonable access to the back side" as an appropriate use of PDR, and lists sharp dents in contoured areas, dents on the edge of panels and dents with cracked paint as inappropriate. Lexus describes the same limits: a shallow large dent or crease can be repaired to an acceptable level, but very sharp dents and creases may not be suitable, and the limiting factors are how flexible the paint is and how far the metal has been stretched.

Check Good for PDR Probably needs paint
Shape of the damage Soft, rounded shoulders, even if the dent is wide Sharp, pinched fold on the line itself
Paint on the line Intact under a magnifier Cracks, chips or crazing on the ridge
Location Middle of the panel Panel edge, hem or a reinforced rail
Access Rod access from behind, or room for glue tabs Double skin with no access and no grip for glue
Metal Local dent, metal not stretched Stretched metal, panel shifted in a collision

Size alone does not decide it. A wide, shallow dent across a door line can be a better job than a two-inch crease folded sharp on the ridge. To read the shape properly, put a line board on the damage and look at it from both ends of the panel (our guide on how to read a dent with a line board explains the stripe patterns).

For the paint, GM suggests a 4x magnifying glass to look for cracks before you start. Do it on the ridge itself. The paint on a sharp edge has the least room to flex, so if it is going to crack, it cracks there.

Getting access to a body line: lamps, trim and glue

Use the openings the car already has; do not drill and do not remove structural parts.

Most body lines on doors can be reached through the window opening or the inner door access holes. Rear quarter lines are often reached by taking out the tail lamp, which leaves an opening straight up the inside of the quarter panel; GM's bulletin names tail lamps, headlamps and hood insulators as the parts to remove for access, and says that drilling holes or removing structural components is not recommended and may void its corrosion warranty.

When there is no way behind the line (a double-skinned section, a reinforcement right under the ridge, a roof rail), glue pulling takes over. The same bulletin says glue pulling makes dent removal possible where there is minimal or zero access to the back side. On a body line, the tab has to sit on the line, not beside it, so pick a tab that matches the shape: a V-shaped crease tab on a sharp ridge, a flat or domed tab on a soft, rounded line. The basics are in our glue pulling guide.

Use an air wedge where you need a gap between panels, and protect the paint and trim around every tool you put in. A new scratch on the edge of the access hole costs more than the dent.

Body line dent repair: the PDR sequence

Release the ends first, then bring the line up from the ends toward the centre in small moves, checking after each pass.

  1. Read and mark. Put the line board on the damage and mark both ends of the low area, the deepest point and any crown (high spot) the impact pushed up beside it.
  2. Take the crown down first. A ridge of high metal next to the dent holds the low in place. Tap it down lightly with a knockdown and a blending hammer before you push anything. If you push first, the crown only gets higher.
  3. Start at the ends. Push the shallow ends of the damage, not the deepest point. Each small push releases a little of the tension, so the centre has somewhere to go. Technicians often call this unzipping the line.
  4. Work toward the centre. Move along the line in small steps from both ends. Use a sharp tip on the ridge itself so you lift the edge, and a softer tip on the flat area beside it.
  5. Glue where you cannot push. Set a crease tab on the line, pull gently, check, and knock down any high the pull made.
  6. Check after every few pushes. Read the board from both ends of the panel. A line can look straight from one side and wavy from the other.
  7. Finish the edge. Small highs along the ridge come down with a knockdown pen held exactly on the line. Then blend the flat area beside it.
  8. Compare with the other side. The line is done when it has the same height and the same sharpness as the matching line on the other side of the car.

Go slowly. The paint on a sharp edge can only take so much movement, and a fast push in the centre is how a repair turns into a respray.

Crease dent repair: why the ends come first

A crease is a fold under tension; pushing its deepest point first locks the fold in and moves the metal around it.

On a crease, the metal on both sides of the fold has been pulled into it. If you push the deepest part straight away, that metal has nowhere to go, so it rolls up into new highs along the sides, or the panel oil-cans somewhere else. Starting at the shallow ends releases the fold a little at a time. Each push makes the next part of the crease softer.

Long creases that run along a door often need many light passes rather than a few strong ones. Keep the pressure low, keep the tip moving along the crease and read it often. When the crease crosses a body line, finish the flat area on both sides first, then rebuild the line last, so the line is not pushed out of shape by work you do next to it.

When to stop and send it to paint

Stop when the paint cracks, when the metal is stretched or when the line will not come back to the height of the other side.

  • The paint cracks on the ridge. It is no longer a paintless repair. Tell the customer before you go further.
  • The metal is stretched. Stretched metal has more surface than it had before. It will not sit flat; it pops in and out, and the line stays soft however long you work it.
  • The fold is too sharp. A crease folded hard on the edge of the line, or on the edge of the panel, can leave a mark that no tip can remove.
  • The panel has moved. If the whole panel shifted in a collision, it is body shop work. Our article on when large dents need paint goes through the same decision for bigger damage.

Saying no to a job you cannot finish clean protects your name more than any repair does.

Tools for body line and crease work

Body lines need three things: a way to read the line, a way to lift it, and a way to knock down the highs on it.

For the push from behind, use rods with sharp and medium tips that reach the line through the access you have; our guide to PDR rod lengths, bends and tips helps you pick them. Every DentPDR tool is made in our own facility, with a 1-year warranty and a 30-day free exchange.

FAQ

Can paintless dent repair fix a dent on a body line?

Often, yes. Soft dents in body lines are a normal PDR repair when the paint is not cracked and the technician can reach the back of the line or pull it with glue. GM's PDR bulletin lists them as an appropriate use. Sharp, pinched dents on the line, dents at the edge of a panel and any damage with cracked paint usually need conventional repair and paint.

Why is a body line dent harder to fix than a dent on a flat panel?

The line is a sharp stamped edge that has to come back to its exact height and crispness, and the reflection along it shows every small error. The paint on the edge has less room to flex, so it cracks sooner. The metal around the line is also stiffer, so it needs many small, accurate moves instead of a few large ones.

How do you fix a crease dent without paint?

Knock down the crowns beside the crease first, then push or pull from the shallow ends of the crease toward its deepest point in small, light moves. This releases the tension in the fold a little at a time. Read the crease with a line board after every few pushes and finish the highs with a knockdown pen.

Do you need to remove the tail lamp to fix a quarter panel body line?

Often, yes. Taking out the tail lamp opens a path up the inside of many rear quarter panels, and OEM guidance names it as an accepted way in. If the line is behind a brace or a double skin, glue pulling with crease tabs is the alternative. Drilling holes for access is not recommended.

Which glue tab works best on a body line?

One that matches the shape of the line. A V-shaped crease tab sits on a sharp ridge and pulls along the edge; a flat or domed tab suits a soft, rounded line. The tab must sit on the line itself, and every pull is followed by a check and a knockdown of any high it made.

Verwandte Leitfäden

Macro photo of a stainless steel PDR knockdown tip touching a high spot on a glossy blue car hood, line board stripes reflected in the paint and a blending hammer with an orange handle behind 4 Min. Hörzeit blending hammer · 11 Min. Lesezeit

Finishing a Dent: Tap-Downs, Blending Hammers and High Spots

A stainless steel PDR slide hammer with a black grip and a brushed steel sliding weight on a charcoal ground, hooked to an orange glue tab, lit by an orange rim light 5 Min. Hörzeit cold glue · 9 Min. Lesezeit

PDR Slide Hammers: Cold Glue Pulls vs Heavy-Duty Pulling

A large shallow dent in the lower half of a white car door, the stripes of a PDR line board bending around it in the reflection, an orange glue tab on a charcoal tool cart in the foreground 5 Min. Hörzeit glue pulling · 10 Min. Lesezeit

Large Dent Repair: When PDR Still Works and When It Needs Paint

WhatsApp