Перейти к содержимому

Страна и язык

1 Корзина
cold glue

PDR Slide Hammers: Cold Glue Pulls vs Heavy-Duty Pulling

The three types of PDR slide hammer, how to match them to cold glue and hot glue, which one fits which dent, and the pull sequence that avoids new highs.

A stainless steel PDR slide hammer with a black grip and a brushed steel sliding weight on a charcoal ground, hooked to an orange glue tab, lit by an orange rim light

Подкаст из мастерской · Прослушивание: 5 мин

Florence, Oliver, Kaan

0:004:22

Транскрипт43 строк

A PDR slide hammer pulls a dent from the outside: a glue tab is bonded to the low spot, the hammer hooks onto the tab, and a sliding weight strikes a stop to send a short, sharp pull into the metal. Which PDR slide hammer you need depends on two things: how much metal has to move and which glue you pull with. Light cold glue pulls on small and hail dents want a compact, controlled hammer; big, soft dents and roughing work want a heavier, longer one. This guide explains the three slide hammer types, how to match them to cold glue and hot glue, and the pull sequence that keeps you from making new highs.

Key takeaways

  • A slide hammer gives a short impulse, not a steady pull. That impulse is what moves a dent from the front when there is no access to the back.
  • Three types: manual (you set the force every stroke), push-spring (a spring helps control the stroke) and trigger auto (a spring fires the pull when you press a pin, one hand).
  • Cold glue suits light, repeated pulls on small and hail dents; hot glue holds harder and suits heavy pulls on large, soft dents.
  • Heavier is not better on small dents. Too much impulse turns a low into a high.
  • Light pulls, check with the board, knock down the high, pull again.

What a PDR slide hammer does in glue pulling

It turns a glue tab on the paint into a pulling point, so you can raise a dent without reaching the back of the panel.

Glue pull repair grew out of PDR, and I-CAR lists slide hammers next to pulling bars, mini lifters and pulling towers as the lifting tools for it. I-CAR also names its main advantage: glue pulling does not require the paint and E-coat to be removed, and it does not damage the back of the panel, so corrosion protection stays in place. That is why a slide hammer is the tool for double-skinned doors, roof rails, braced areas and quarter panels where a rod cannot reach.

The difference to a lifter or a bridge puller is the kind of force. A lifter applies a steady, metered pull. A slide hammer applies one short jolt each stroke. The jolt is good for breaking a dent loose and moving a lot of metal fast; the steady pull is better for the last, fine lift on a sharp low.

Three types of slide hammer: manual, push-spring and trigger auto

All three hit a stop with a sliding weight; they differ in who controls the force and how many hands it takes.

Type How it pulls Best for Watch out for
Manual (standard) You throw the weight back by hand; force depends on your stroke Big, soft dents, roughing, heavy hot glue pulls Pulls are less even from stroke to stroke; easy to overpull
Push-spring A spring in the body controls the stroke and the hit Daily glue pulling, hot or cold glue, repeatable pulls Pick the length for the reach and leverage you need
Trigger auto A spring is loaded, then fires when you press a pin One-handed cold glue pulls on roofs and hoods, hail Made for cold glue pulls; not a roughing hammer

A manual hammer is the simplest and gives the most raw force, but every pull is only as even as your arm. A push-spring hammer makes the hit smoother and easier to repeat, which matters when you pull the same dent ten times. A trigger hammer frees your other hand: you hold the panel, the light or the line board while the tool fires the pull.

Cold glue or hot glue: matching the hammer to the glue

Match the hammer to the glue, and the glue to the dent and the temperature.

Cold glue needs no heat. You knead it by hand, press the tab on, and pull within seconds. The bond is softer than hot glue, so it suits many light pulls: small dents, hail fields, crown work and quick mobile jobs. Cold glue works best with a compact push-spring or trigger hammer, because a light, controlled hit is what the bond can carry. Temperature range matters more than the tool: a glue rated for the day's conditions holds; the wrong one slips mid-pull.

Hot glue is melted on the tab, bonds as it cools and is released with alcohol. It holds harder and takes a bigger impulse, so it pairs with heavier manual hammers on large, soft dents where most of the metal has to come up first. Our guide on how to glue pull a dent covers tab shapes, glue temperature and release.

A simple rule: if the tab keeps popping off before the metal moves, the hit is too hard for the glue or the panel was not clean. A heavier hammer will not fix that; cleaner paint, the right glue or a lighter hit will.

How to choose a PDR slide hammer for the dent

Choose by the amount of metal to move and by the space you have to work in.

Dent Glue Hammer
Door ding, small round dent Cold glue or small hot glue tab Compact push-spring or short trigger hammer
Hail on a roof or hood Cold glue, many tabs Trigger auto (one hand, many pulls) or push-spring
Large, soft dent on an open panel Hot glue, large tab Long, heavy manual hammer for the bulk, then lighter pulls
Roof rail, braced area, no rod access Either, by temperature Long push-spring for reach and leverage
Sharp, small low after the bulk is up Small tab A lifter, or the lightest hammer stroke

Length gives leverage and reach; weight gives impulse. A long, heavy hammer is right for the first pulls on a big dent, as our guide on large dent repair describes. The same hammer on a door ding will overpull it on the first stroke.

The slide hammer pull sequence that avoids new highs

Pull light, read the panel, knock down, then pull again; never try to finish a dent in one hit.

  1. Clean the paint. Wax, sealant and dust weaken the bond and cause uneven releases. Clean the spot and a margin around it.
  2. Pick the tab. Round tabs for round dents, long or crease tabs for lines. The tab should cover the low, not the shoulders around it.
  3. Set the tab at the deepest point of the area you pull now. On a large dent that means the outer lows first, the centre last.
  4. Pull in line. Hold the hammer straight out from the panel. An angled pull moves metal sideways and can raise the wrong area.
  5. Start soft. Use a short stroke or the lightest spring setting first. Add force only if the metal does not move.
  6. Check after every pull or two. Read the line board. Where the pull made a high, tap it down with a knockdown before the next pull.
  7. Release the tab cleanly. Alcohol for hot glue; peel or roll off cold glue. Never rip a tab off by force.

I-CAR lists knockdown tools beside the lifting tools for a reason: in glue pulling, the pull and the knockdown work as a pair.

PDR slide hammers in our range

Three hammers cover the three jobs above. All specs are from the product pages.

  • One-handed cold glue pulls. The Kangaroo Long Trigger Auto Slide Hammer Set is developed and produced by DentPDR. A spring-loaded trigger fires the pull when you press the pin on the side, so you can pull with one hand on roofs and hoods. The set comes ready for cold glue with summer and winter cold glue, a tab adapter, 4 tabs in different sizes and a carrying case. A short model is available for tighter areas.
  • Controlled, repeatable pulls with hot or cold glue. The Scorpion Long Push-Spring Slide Hammer Set is 35 cm closed and 50 cm open, weighs about 900 g without the case, has a locking cap and works with hot and cold glue. It comes with 4 tabs and a carrying case.
  • Heavy pulls on big dents. The DentPDR Heavy-Duty Stainless Steel Slide Hammer (57 cm / 1600g) has a 1,600 g total weight and a 57 cm stainless body, and takes hot glue, cold glue, standard tabs and adapters.

DentPDR tools are made in our own facility, with a 1-year warranty and a 30-day free exchange. You can pay via PayPal, with PayPal's 180-day buyer protection.

FAQ

What is a slide hammer used for in PDR?

In paintless dent repair a slide hammer pulls a dent from the outside of the panel. A glue tab is bonded to the low spot, the hammer is connected to the tab, and a sliding weight strikes a stop to give a short pull. It is used where there is no access to the back of the panel, and to lift the bulk of a large, soft dent quickly.

Is cold glue or hot glue better with a slide hammer?

Neither is better for every job. Cold glue needs no heat and suits many light pulls on small dents and hail, with a compact push-spring or trigger hammer. Hot glue bonds harder and takes a bigger hit, so it suits heavy pulls on large, soft dents. Always pick a glue rated for the day's temperature.

How heavy should a PDR slide hammer be?

Heavy enough to move the metal, light enough not to overpull it. Heavy, long hammers suit large dents and roughing, where a lot of metal has to come up first. Lighter or spring-controlled hammers suit small dents and finishing pulls. Many technicians carry one of each and switch as the dent gets smaller.

What is an automatic or trigger slide hammer?

A trigger slide hammer stores the pull in a spring and fires it when you press a pin, instead of you throwing the weight by hand. You can pull with one hand, which helps on roofs and hoods where you need the other hand for the panel or the light. It is made for cold glue pulls, not for heavy roughing.

Can a slide hammer damage the paint?

Used with PDR glue and tabs on intact factory paint, a slide hammer pulls the metal without removing the coating. Risks come from overpulling, which makes a high, from pulling at an angle, and from ripping a tab off instead of releasing it. Cracked or repainted panels can lose paint when the tab comes off, so check the finish before you glue.

Building a glue pulling setup? Start with one controlled hammer for cold glue and add a heavy one for big dents. For removing dents from behind the panel, see our guide to PDR rod sets.

Связанные руководства

Macro photo of a stainless steel PDR knockdown tip touching a high spot on a glossy blue car hood, line board stripes reflected in the paint and a blending hammer with an orange handle behind Прослушивание: 4 мин blending hammer · Чтение: 11 мин

Finishing a Dent: Tap-Downs, Blending Hammers and High Spots

The rear quarter panel of a graphite-grey car in a PDR workshop at sunset, a crease dent kinking the golden reflection along its body line, PDR rods racked by the open door and an orange glue tab on a cart Прослушивание: 4 мин body line · Чтение: 11 мин

Body Line Dent Repair: When PDR Can Fix a Crease

A large shallow dent in the lower half of a white car door, the stripes of a PDR line board bending around it in the reflection, an orange glue tab on a charcoal tool cart in the foreground Прослушивание: 5 мин glue pulling · Чтение: 10 мин

Large Dent Repair: When PDR Still Works and When It Needs Paint

WhatsApp