Finishing a dent in PDR means taking the panel from "pushed out" to "invisible": you read the repair under a line board, tap down every high spot with a knockdown and a blending hammer, push the small lows that the tap-down uncovers, and repeat until the reflection runs straight in every direction. The push removes the dent; the finish removes the evidence. This guide covers how to find the highs, which tap-down tip to use on which paint and panel, how heavy the hammer should be, and the loop that turns a good repair into one the customer cannot find.
Key takeaways
- Every push leaves a little crown around it. Finishing is the loop of knocking those highs down and picking the lows they hide, not one final tap.
- Read the panel from two or three angles under the light before you tap. A high spot that only shows from one side is still a high spot.
- Pick the tip by the job: soft nylon or PEEK for blending and fresh or soft paint, a domed stainless tip for a tight, defined crown, a sharper tip only for a small, hard high.
- Many light taps beat a few hard ones. A hard hit on a crown moves metal past flat and makes a new low.
- Stop when the reflection is straight from every angle and the panel matches the orange peel around it.
What finishing a dent means in PDR
Finishing is the stage after the dent is lifted, where you remove the small highs and lows that the push left behind.
When you push a dent from behind, the metal does not rise as one smooth sheet. Each push lifts a small area, and the metal around that point rises a little too. After the main lift, the repair is close to flat, but under a line board it shows a pattern of small crowns (highs) and soft dips (lows), often with a ring of tension around the old dent.
Finishing turns that pattern into a surface that reads like the rest of the panel. It uses three moves, again and again:
- Tap down: lower a high spot from the paint side with a knockdown and a hammer.
- Pick: raise a small low from behind with a sharp or medium rod tip.
- Blend: soften the edge between the repair and the untouched panel with light, spread-out taps.
The training schools describe the same order. PDR Workshop's standard dent sequence is push the centre, knock down the high spots to flat, pick the micro lows, knock down the soft high that is left, then tap to finish until there are no more shadows. Push and knockdown are not two stages; they take turns.
How to find high spots on a panel
You find high spots with a line board or light held so the stripes cross the repair, and you look from more than one angle.
On a line board, a high spot pinches the stripes together or bends them away from the light; a low spot spreads them apart or pulls them in. A soft crown shows as a gentle bulge in the lines, a sharp one as a small, bright knot. If you are new to reading reflections, our guide on how to read a dent with PDR lights and line boards explains the patterns.
Three habits catch the highs that beginners miss:
- Move the board, not only your head. Turn the stripes across the repair at two different angles. A crown that runs in the same direction as the stripes hides from them.
- Look from both ends of the panel. A high on the far side of a dent can look like part of the low from one end.
- Use your hand. Slide a flat palm or the back of your fingers across the area with light pressure. A crown you can feel is too high to leave.
Mark what you find before you touch the hammer. A marker on the board, a strip of tape on the panel edge, or simply naming the spot ("high at two o'clock, low at the centre") keeps you from chasing a reflection that moved because your head did.
Tap-down tips: nylon, PEEK or steel?
Match the tip to the paint and the crown: plastic for blending and soft paint, stainless steel for a defined, tight high.
Most knockdowns take interchangeable tips on a 5/16 or M8 thread, so one pen can carry the right tip for each stage of the finish. The material decides how much force reaches the metal and how easily the paint marks:
| Tip | Feel on the panel | Use it for | Watch out for |
|---|---|---|---|
| Nylon / plastic, flat or domed | Soft, spreads the blow | Blending large, soft crowns; fresh or soft paint; the first pass on any high | Too soft to move a hard, small crown; edges wear and flatten over time |
| PEEK (hard engineering plastic) | Firmer than nylon, still paint-friendly | Most daily knockdown work; crowns beside body lines; finishing passes | Keep the face clean: grit on any plastic tip scratches clear coat |
| Stainless steel, domed | Direct, moves metal fast | Tight, defined crowns; high-tension areas such as roof rails and edges of body lines | Marks paint with one heavy hit; cover the face with tip tape on delicate paint |
| Stainless steel, sharp or pointed | Very concentrated | A single small, hard high; working along a crisp line | Leaves a dimple if you miss or hit hard; last tool, not first |
A practical rule: start one step softer than you think you need. If the crown does not move after a few controlled taps, go one step harder. Going the other way, from a steel point to a nylon dome, usually means you already made a low.
Keep the tip face round, clean and free of nicks. A chipped plastic face or a burr on a steel tip prints straight into the paint, and that mark is harder to remove than the high was.
PDR blending hammer: weight, face and how to swing it
Use a light hammer that falls by itself, and let rhythm, not force, move the metal.
A blending hammer is not a body hammer. It is used to tap a knockdown or to strike the panel lightly through a soft face, and the goal is many small, even blows. A lighter hammer gives you more control and less fatigue over a long finish; a medium-weight hammer moves stubborn crowns with fewer taps but punishes a bad aim. Many technicians keep both.
- Grip: hold the hammer loosely, near the end of the handle, and let it bounce back after each tap. A tight grip turns taps into blows.
- Swing: move from the wrist, a short arc of a few centimetres. Speed up the rhythm before you raise the force.
- Face: a hammer with a threaded head can take the same tips as your knockdown, so you can blend straight on the panel with a soft face and switch to a tip for a defined high.
- Angle: keep the knockdown square to the panel at the exact spot. An angled tip slides and lands beside the crown, which makes a new low.
The finishing loop, step by step
Finishing is a loop of read, tap, pick and read again until nothing moves the reflection.
- Read. Set the board so the stripes cross the repair. Find the highest crown first, not the nearest one.
- Tap the crown down. Start at the outer edge of the high and work in toward its peak in a tight spiral or a line of taps. Light taps, close together.
- Read again. Knocking a crown down often reveals small lows that were hiding beside it. That is normal, not a mistake.
- Pick the lows. From behind, with a sharp or medium tip, lift each micro low with small, precise pushes. Stop just short of flat; the next tap-down will settle it.
- Tap the soft high left by the picks. Smaller and lighter than the first knockdown.
- Blend the edge. With a soft tip, tap a ring around the whole repair so the transition into the untouched panel disappears.
- Repeat until the stripes run straight from every angle you check.
Each loop is smaller than the last. If a loop makes the area bigger or the highs sharper, slow down: your taps are too hard or landing off the crown.
Common finishing mistakes
Most finishing problems come from too much force, too little reading, or the wrong tip.
- Knocking past flat. One heavy hit on a crown sinks it into a low, and now you need access behind it again. Light taps, then read.
- Chasing reflections. If you move your head between taps, the "high" moves too. Keep the board and your eye still while you work one spot.
- Leaving a halo. A repair that is flat in the middle but carries a ring of crown around it still shows. Blend the ring.
- Marking the paint. A steel tip straight on soft or fresh paint, or a dirty plastic tip, leaves dimples or scratches. Use a soft tip first and keep tip tape on hand.
- Stopping on one angle. The customer will look at the car from angles you did not. Check from both ends and from above before you call it done.
The same loop finishes every kind of damage, from a door ding to a body line or crease; on a body line the highs sit beside the ridge, so the tip has to be narrow enough to land on them and not on the line.
When is a dent finished?
A dent is finished when the reflection runs straight from every angle and the surface texture matches the panel around it.
Three checks before you hand the car back: the stripes of the line board run straight across the repair when you turn the board two ways; the light shows no shadow or bright spot when you walk from one end of the panel to the other; and the orange peel in the repair looks the same as the factory texture next to it. If all three pass, there is nothing left for the customer to find.
Tools for tap-downs and blending
You need a knockdown with a range of tips, a light hammer, and a board to read the work.
- Knockdown with interchangeable tips: the DentPDR 11-Piece Knockdown Pen Set (Aluminum Body / M8 & 5/16) has a lightweight aluminium body that keeps your hand fresh over a long finish, and precision-machined stainless steel tips for tapping, crown reduction and blending, on 5/16 or M8 thread.
- A hammer, a pen and soft tips in one kit: the PDR Plastic Hammer (Spatula Handle) + Knockdown Pen + 8 Interchangeable Tips is a simple starting set for knockdown work.
- Reading the finish: the DentPDR Foldable Dent Reflector Line Board (80cm / 31.5") gives an 80 cm striped reflection with no power needed.
For picking the lows from behind, use rods with sharp and medium tips; our guide to PDR rod lengths, bends, tips and threads helps you choose them. Every DentPDR tool is made in our own facility, with a 1-year warranty and a 30-day free exchange.
FAQ
What is a tap down in PDR?
A tap down, or knockdown, is a tool you hold on the paint side of the panel and strike lightly with a hammer to lower a high spot. It has a handle and a tip, usually interchangeable on a 5/16 or M8 thread, in nylon, PEEK or stainless steel. Technicians use it after each push to bring crowns back to the level of the panel, and again at the end to blend the repair.
What is the difference between a blending hammer and a body hammer?
A blending hammer is light and made for many small, controlled taps on a knockdown or through a soft face. Its job is to refine the surface, not to reshape metal. A body hammer is heavier, with a steel face, and is made to move metal in panel beating. Using a body hammer on a PDR finish usually sinks the crown and marks the paint.
Which knockdown tip should I start with?
Start with the softest tip that can move the crown, usually nylon or PEEK. Plastic tips spread the blow and protect the paint, which makes them right for blending and for fresh or soft paint. If the high does not move after a few controlled taps, move one step harder to a domed stainless tip. Keep sharp steel tips for a single small, hard high.
Why does a new low appear after I knock down a high spot?
Because the high was hiding it, or because the tap was too hard. When you lower a crown, the lows beside it become visible on the line board. That is part of the loop: pick those lows from behind, then tap the soft high the picks leave. If lows appear where there were none, your taps are too heavy or landing beside the crown.
How long does finishing take compared to the push?
On a clean repair, finishing often takes as long as the push itself or longer, because each loop is small and slow. Experienced technicians do not see that as lost time: the push decides whether the dent is gone, but the finish decides whether anyone can still see where it was.












